Scientific & Laboratory Instruments

Consists of S.S. holders in manifold of 3 of 6 to hold 47 mm dia, membrane filter. The top of the holders are connected to the outlets of the flushing tube with silicone tubing & glass stop cock. A vacuum resistant flask or woof bottle must be placed between the manifold & vacuum pump. Supplied without Wolfs Bottle & vacuum / Pressure pump. These units are used for sterility testing when the membranes filter is to be removed from the holder for incubation in culture media. Filtration areas is 12.5 cm & has a holding capacity of 250 ml. though only vacuum is required for filtration; some pressure is required for flushing liquids.

Product Details:

Descriptions:

Double walled inner made of thick stainless steel / mild steel, outer made of heavy duty mild steel / G.I. duly powder coated. Temperature accuracy 2°C controlled by thermostatic.

Specifications:

Accessories for Oven:

Product Details:

Model Overview:

• Range: 0.00 to 2.50 mg/L(5.00 mg/L) Some meters allow the user to extend the range to the value between the brackets

Product Details:

Description:


Scope : This method describes the procedure for determining the flash and fire points of petroleum products, except fuel oils and those products having an open – cup flash point below 70*C.

Outline of the Method : The test cup is filled to specified level with the sample. The temperature of the sample is increased fairly rapidly at first and then at a slow constant rate as the flash point is approached. At specified intervals, a small test flame is passed across the cup. The lowest temperature at which application of the test flame causes the vaporous above the surface of the liquid to ignite momentarily is taken as the flash point.

To determine the fire point, the test is continued until the application of the test flame causes the oil to ignite and burn for at least 5 seconds.


Preparation of Apparatus : Support the apparatus on a level steady table in a drought free room or compartment. Shield the top of the tester strong light by any suitable means to permit ready detection of the flash point.

Wash the test cup with an appropriate solvent to remove any oil or traces of gum or residue reaming from a previous test. If any deposits of carbon are present, they may be removed with steel wool. Flush the cup with cold water and dry for a few minutes over and open flame or a hot plate to remove the last traces of solvent and water. Cool the cup to a point at least 56*C below the expected flash point before using.

Support the thermometer in a vertical position with the bottom of the bulb 6 mm from the bottom of the cup and locate at a point half way between the center and side of the cup on a diameter perpendicular to the are (or line) of the sweep of the test flame and on the side opposite to the test flame burner arm.

Note : The immersion line engraved on the thermometer is about 2 mm below the level of the rim of the cup when the thermometer is properly positioned.

Procedure : Tests shall not be performed in a laboratory hood (seen note) or at any other location where droughts occur. During the last 17 deg. rise in temperature prior to the flash point, care shall be taken to avoid disturbing the vaporous in the test cup by careless movements or breathing near the cup.

Note: With some samples where vapors or products of pyrolysis are objectionable, it is permissible to place the apparatus with shield in a hood, the drought of which is adjustable so that vaporous may be withdrawn without causing air currents over the test cup during the final 56 Deg rise in temperature prior to the flash point.

Note: Viscous samples may be heated until they are reasonably fluid before being poured into the cup; however the temperature during heating shall not exceed 56 deg below the probable flash point.

Correction for Barometric Pressure : If the barometric pressure at the time of the test is less than 715 mm Hg, record it and add the appropriate correction, given below to the flash and fire point values as determined in 5.5 and 5.6.

THE SCIENTIFIC MALL LUTRON / FLUKE / HTC / WACO / KUSAM MECO / JAYANT / EUTECH / HANNA / WHATMAN / SHIMAZU / LEIMCO / ZEAL / RAYTEK / ATAGO / ERMA / OPTIC GLASS CUVETTES GLASS & QUARTS / LOVIBOND / BARIGO / OREGON / WORK ZONE / YUYUTSU / MARIENFIELD / BLUE STAR / ROHEM / MEXTECH / PALL / SARTORIOUS / BROOKFIELD / INFUSIL / THIASIL / HAMILTON.......AND MANY MORE

Additional Information:

• Item Code: THE-SCIENTIFIC-MALL
• Minimum Order Quantity: 1 Onwards

Product Details:

Backed with our profound experience in the domain of Exporting , supplying and trading, we are able to render a comprehensive range of Portable Autoclave. The rendered product possesses a lid which is made up of quality approved steel and is attached with a cylindrical shaped cooker that in smaller in size with a lesser stream pressure for infection reduction. It comprises easy grip along with a smaller breathing space. The offered product also comprises two Stainless-steel safety valves.

 

Features:

 

• Reliable
• Smooth functioning
• Ensures safety
• Easy to use

Product Details:

Description:

Autoclave Portable Laboratory Instrument with complete stainless steel, electrically with air release nozzle. With gasket, lid, safety valve, pressure gauge & steam release cock.

Features:
 

• Lid is made of S.S.304 heavy gauge die pressed
• Equipped with pressure gauge, steam release valve & 2 Safety valves
• Supplied with S. S. perforated basket
• Fitted with silicon rubber gasket joint less
• Work in 230 Volts 50Hz
• Foot lifting arrangement to open lid

Product Details:

With the help of our expert team of professionals, we are able to offer a commendable range of Autoclave Vertical Laboratory Instrument.The inner body of the offered product is made of quality approved, thick stainless steel (304) and the outer body is also made of the same. The offered products ensures absolute leak-proof. Moreover the offered product also comprises pressure gauge, pressure release valve, S.S. basket, safety valve, water level indicator, with cord, Plug, & Pressure Control Switch.

 

Features:

 

• Longer functioning life
• Cost-effective
• Robust design
• Includes Safety assurance

 

Specifications: 

Optional accessories:

Descriptions:

Rectangular Thermostatic contain Double walled construction. Inner chamber of stainless steel sheet and outer of mild steel sheet duly finished in powder coated. The gap is filled with glass wool for temp. insulation. Temperature range 50C above ambient to 900C controlled by a thermostat. Complete with concentric rings, pilot lamp, plug cord etc. To operate on 220 V AC 50 Hz single phase.

 

Specifications:

 

We provide a premium quality Tablet Disintegration Test Machine to our clients. 

Specifications
 

• Temperature: 25.0°C to 40.0°C
• Accuracy: Better than ± 0.3°C
• Resolution: 0.1°C

 

Features

(A) Digital only temperature single basket without beaker
(B) Digital only temperature double basket without beaker

Hot Air Oven Heating Mantles Temperature Upto 300 ' C With Energy Regulator The Body of the mantle is spun without joint duly painted (one piece). The Mantles are flexible Glass Fabric provided in housing. Heating Mantle is lagged with special grade mineral wool. Each Mantle is fitted with 'ENERGY REGULAR' for maintaining temperature and with pilot lamp complete with 3 core wire .

Specifications: 

• Work On: 220Volts A.C
• Colour: White and blue 
• Temperature:300C 

We are the leading Exporter, Trader and supplying of Hydrometers of superior quality range. Hydrometers is a device to measure relative density of liquids such as Grease, oil etc. Components used in a hydrometer are glass frame, cylindrical stem and bulb floating in the mercury fluid. To test the density of a liquid, we use a long glass jar. The jar is filled with liquid and hydrometer is floated inside the fluid. The liquid surface touches the stem of hydrometer at specific point, which indicates specific gravity of that fluid.

 

Specifications:

 

Sikes Hydrometer at 51ºF, Zeal England:

• Range: 0/20 A 0/20 20/40 40/60 60/80 80/100
• Alcohol meter (V / V, Volume By Volume) Zeal U.K. at 15.6ºC
• Range: 0-20, 20-40, 40-60, 60-80, & 80-100
• JAWA (Brix) Hydrometers with work Certificate Germany
• Range: No.1 - 2 to 13 No.2 - 13 to 21 No.3 - 19 to 27
• Heavy Liquid Hydrometers, Germany Sp.Gr.1000/2000 & BE 0/70
• Light Liquid Hydrometers, Germany Sp.Gr. 700/1000 & BE 10/70
• Heavy Liquid Hydrometers, 305 mm Long, Range - 1.000 / 2.000 & 0/70 Baume
• Light Liquid Hydrometers, 230 mm Long, Range : 700 / 1.000
• Baume Hydrometers, Germany at 20ºC
• Range: 0/10, 10/20, 20/30, 0/20, 0/30, 0/40, 0/50, 30/40 & 40/50
• Baume Hydrometers, Digital, Atago, Japan Model PAL-84S, Range : 0.0 - 210
• Twaddle Hydrometers German at 60ºF, No. 1, 2, 3, 4, 5, & 6
• Twaddle Hydrometer Zeal England at 84ºF, No. 1, 2, 3 & 6
• Twaddle Hydrometer Zeal England at 84ºF, No. 4 & 5
• Brix Hydrometer w/o Thermometer Germany at 20ºC
• Range: 0/10, 10/20 & 20/30
• Brix Hydrometer w/o Thermometer Germany at 27.5ºC
• Range: 0/10, 10/20, 20/30, 30/40, 0/30, 30/60 & 60/90
• Brix Hydrometer with Thermometer Germany at 27.5ºC & 20ºC
• Range: 0/10, 10/20, 20/30, 0/30, 30/60 & 60/90
• Brix Hydrometer with Thermometer Germany GDR, German at 27.5ºC & 20ºC
• Range: 0/10, 10/20 & 20/30
• Brix Hydrometer with Thermometer German with NPL Certificate
• Brix Hydrometer, Sugar Percent Temp. 27.5ºC Made in West Germany
• Specific Gravity Hydrometers, Germany at 20ºC 600/700, 700/800, 800/900 & 900/1000 & 800/10001000/1100, 1100/1200, 1200/1300, 1300/14001400/1500, 1500/1600, 1600/1700, 1700/18001000/1200, 1200/1400, 1400/1600, 1600/1800, 1800/2000
• 800/1000 GDR German Make
• Sikes Table Book Indian
• Soil Hydrometer, Zeal England, ASTM 152 H Range: 5 to 60 gm / ltr, Temp: 68ºF

 

We are the leading Exporter, Trader Suppliers and Dealers of Hydrometers in Tamilnadu, Kerala, Karnataka, Andhra Pradesh, Orissa, Uttaranchal, Tripura, Sikkim, Rajasthan, Punjab, Nagaland, Mizoram, Meghalaya, Manipur, Maharashtra, MadyaPradesh, Jharkhand, Jammu and Kashmir, Himachal Pradesh, Haryana, Gujarat, Goa, Chhattisgarh, Bihar, Assam, Arunachal Pradesh, West Bengal, Uttarpradesh, Chandigarh, Delhi, Lakshadeep, Pondicherry, Daman and Diu, Dadar and Nagar Haveli.

 

Triple walled inner made of thick stainless steel / mild steel, outer made of heavy duty mild steel / G.I. duly powder coated. Temperature range 50°C to 250°C Temperature accuracy +/- 2°C controlled by thermostatic. Heaters placed left & right side in the inner chamber .

Specifications:

 

 

Accessories for Oven:

 

• Digital Temperature indicator cum Controller
• Air circulation Fan with Motor
• Digital timer with Temperature Controller

We are suppliers of Blood Lancets Instrument.

Specification:

• Medipoint blood lancets, U.S.A., (Pkt of 200 Pcs)
• Medipoint blood lancets, U.S.A., (Box of 10,000 Pcs)
• Readypoint blood lancets Korea (Pkt of 1000 Pcs)
• Readypoint blood lancets Korea (Box of 10000 Pcs)
• Imported blood lancets (Box of 200 Pcs) (Pkt of 200 Pcs)
• Imported blood lancets (Box of 10000 Pcs) (Box of 10000 Pcs)
• Disposable Plastic Blood Lancets for Glucometer Imported (Pak of 100)

Our clients can avail from us a wide range of Polarimeter, used in Education, Research and Quality control industries. These are suitable for testing sugar solution and other optically active liquids and are manufactured using quality basic material and components. Offered at competitive prices in the market, these are available in following models:

Features:

• ATAGO Japan Model POLAX 2L (Semi Automatic).

• Digit Polarimeter ATAGO Japan Model RX – 5000.

• Digital AUTOMATIC Polarimeter ATAGO Japan Model AP 100 (Fully Automatic).

• Digital P, imported make.

• Digital Polarimeter Indian Model : EQ-801.

• Polarimeter (220 mm) GNI make Indian Tube having both angular & sugar scale with Rotating Triple Shadow effect with fine optics, suitable for sugar industries without Lamp Assembly.

• Polarimeter (400 mm) GNI make Indian Tube having both angular & sugar scale with rotating Half shadow, without Lamp Assembly.

• Polarimeter (400 mm) GNI make Indian with fine optics and Rotating triple Shadow without Lamp Assembly, Best for Sugar Industries.

• Polarimeter Tubes, Center / Side Filling, Optically True

 

We are the leading Exporter , Suppliers and Dealers of Polarimeter in Tamilnadu, Kerala, Karnataka, Andhra Pradesh, Orissa, Uttaranchal, Tripura, Sikkim, Rajasthan, Punjab, Nagaland, Mizoram, Meghalaya, Manipur, Maharashtra, MadyaPradesh, Jharkhand, Jammu and Kashmir, Himachal Pradesh, Haryana, Gujarat, Goa, Chhattisgarh, Bihar, Assam, Arunachal Pradesh, West Bengal, Uttarpradesh, Chandigarh, Delhi, Lakshadeep, Pondicherry, Daman and Diu, Dadar and Nagar Haveli.

Size in Inches:

• 5” X 5”
• 8” X 8”

Description:

Most Advance Beach top ultrasonic cleaner for surgeon, hospitals & laboratories puts an end to the potentially dangerous, inefficient, ineffective hand scrubbing of delicate expensive instruments by adopting the cleaning technology used world over.

 

Features:

 

1. SMPS power source ensure an amazing >90 % efficiency, compared to 60% of conventional liner source. 
2. 50% of the weight and size of conceptional machines.
3. Energy saving faster cleaning, higher reliability.
4. Optional mechanical or pre settable 99 minutes digital countdown timer with display.

Specifications:

Features:

• Maximum Surface Temperature 350 Deg ºC coated with Energy Regulator/ Thermostatic Controller.

• Steel epoxy coated case for structural strength to support heavy loads.

• A choice of Standard or Electronic control models

• Cast-iron top resists physical abuse and thermal shock

• Embedded heating elements transfer heat across the entire top plate surface

• Temperature uniformity at 150°C ±10°C Temperature stability at 150°C±5°C

 

Size in Inches : 10” X 12”, 10” X 16”, 12” X 18”, 18” X 24”

 

Hot Plate Round Top made of cast iron and body of Mild steel powder coated with Energy Regulator / Thermostatic Controller. Hot plate has the same construction and finish as the rectangular one except that hot plate mounted on a thick mild steel sheet body has a smooth surface cast iron top of 20 cm dia. Heated with an electrically operated element layed under the plate. A three heat rotary switch which work on 220/230V AC. Temperature is controlled by energy regulator. The top is finished in black heat resistant paint. The body is finished in stove enamel paint. The hot plate has pilot lamp.

Features:

• 20 cm round

• Rectangular in different sizes

• Option: Electronic Digital temperature controller cum indicator

Size in Inches : 8” Dia, 9” Dia, 12” Dia

Hot Plate are in Rectangular & Round Shapes. Choice of controller either energy regulator or thermostat. Maximum surface temperature 300 ºC body made of thick stainless steel Operates on 230 volts.

Size in Inches:

• 8” Dia (Round)
• 9” Dia (Round)
• 12” Dia (Round)
• 25×30 cm (Rectangular)
• Align="center">25×40 cm (Rectangular)
• 30×45 cm (Rectangular)
• 45×60 cm (Rectangular)

Descriptions:

We supplied and provide superior quality Bacteriological Incubator which is fabricated using qualitative raw material. Our bacteriological incubators are triple walled with the outer body fabricated with mild steel while the inner body in mild steel, or stainless steel. The inner body is lagged with glass wool and the temperature controlled by capillary type hydraulic thermostat, temperature range 5ºC above ambient to maximum 60ºC with accuracy range of /-2ºC. Within the incubator, glass door is available. The three side heaters manufactured from nichrome wire provided by memmert model.

 

Specifications:

Accessories for Incubator:

Description:

We provide wide range of Ovens Cum Incubator. Double walled, outer of mild steel powder coated and inner is made of either Mild Steel /Stainless steel .Supplied with two separate thermostats one for incubator and one for oven. Teflon glass is provided to see the view .Temperature range 5 ºC above ambient to 200 ºC

Specifications:

Optional Accessories:
 

Digital Temperature Controller

Bulk Density Apparatus is a microprocessor based instrument designed to study the packing down of powder beds of different pharmaceutical & chemical powders and gives accurate & repeatability of the result. Bulk Density is an essential test required in the process of Tablet manufacturing, capsules filling and cosmetics manufacturing as important part of quality control program. 4 digit microprocessor based Pre-set counter provided to set exact no of strokes. This feature eliminates the tedious calculation of Timer Mode. A common holder for both the cylinder drops down smoothly from the specified height. Easy to lock cushioned holders are provided to hold the cylinder. In power failure, the non-volatile memory of the microprocessor remember the last mode of operation, and complete the test after the power supply is resumed.Supplied without cylinder.

We supplied and provide superior quality Bacteriological Incubator Lab Type which is fabricated using qualitative raw material. Our bacteriological incubators are double walled with the outer body fabricated with mild steel while the inner body in mild steel, or stainless steel. The inner body is lagged with glass wool and the temperature controlled by capillary type hydraulic thermostat, temperature range 5ºC above ambient to maximum 60ºC with accuracy range of /-2ºC. Within the incubator, glass door is available.

Specifications:

Accessories for Incubator:

Variable speed mixer to eliminate hand mixing. Holding tube against vibrating rubber cup does rapid mixing of contents. Speed regulator controls the degree of vibration. A unique touch feature operates the unit when the tube is pressed on the rubber cup.Interchangeable adaptors greatly enhance the use of Cyclo Mixer for mixing in different applications.
• Adaptor (CM-01/01) for mixing upto 18 Micro tubes( 6 x 0.5 ml, 6 x 0.4 ml, 6 x 1.5 ml)
• Adaptor (CM-01/02) useful for tube, bottles or flasks upto a maximum capacity of 250 ml.

Additional Information:

• Item Code: CM-101

Backed by our efficient workforce, we are capable of providing our clients with Binocular Medical Microscope. All our products are widely used to increase the operational convenience by combining innovative design & high performance optics. Apart from this, our team of expert quality controllers thoroughly checks all the products on various parameters to remove any defect that may occur during transportation.

 

Features:

 

• Coaxial focusing system
• Ball bearing guide ways
• All parts pressure die cast